#              model: SXT 5nD r2
#      serial-number: 5E9A05706137
#      firmware-type: ar9344
#   current-firmware: 3.33
#   installed-version: 6.49.10
# Flags: U - undoable, R - redoable, F - floating-undo 
#   ACTION                                   BY               POLICY             
# 
# software id = QVZL-7CV2
#
# model = SXT 5nD r2
# serial number = 5E9A05706137
/interface wireless
set [ find default-name=wlan1 ] adaptive-noise-immunity=ap-and-client-mode antenna-gain=0 comment="UPLINK VIZTORONY" country=uzbekistan disabled=no frequency=5180 frequency-mode=superchannel installation=any mode=station-bridge radio-name=Bdrszcs scan-list=5000-6000 ssid=RLAN_PBDRSZCS station-roaming=enabled wireless-protocol=nv2-nstreme
/interface ethernet
set [ find default-name=ether1 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full
/interface pppoe-client
add add-default-route=yes disabled=no interface=wlan1 keepalive-timeout=60 max-mru=1480 max-mtu=1480 mrru=1600 name=pppoe-out1 password=int6662 use-peer-dns=yes user=servizbodor1@rlan
/interface wireless nstreme
set wlan1 comment="UPLINK VIZTORONY" enable-nstreme=yes
/interface wireless manual-tx-power-table
set wlan1 comment="UPLINK VIZTORONY"
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=3des
/ip pool
add name=dhcp_pool1 ranges=192.168.1.100-192.168.1.253
/ip dhcp-server
add address-pool=dhcp_pool1 authoritative=after-2sec-delay disabled=no interface=ether1 name=dhcp1
/snmp community
set [ find default=yes ] addresses=86.109.64.0/27
/system logging action
set 0 memory-lines=100
set 1 disk-lines-per-file=100
set 3 remote=86.109.64.16
/user group
add name=backup policy="ssh,read,sensitive,!local,!telnet,!ftp,!reboot,!write,!policy,!test,!winbox,!password,!web,!sniff,!api,!romon,!dude,!tikapp"
#error exporting /interface bridge calea
/ip neighbor discovery-settings
set discover-interface-list=!dynamic
/ip address
add address=192.168.1.254/24 interface=ether1 network=192.168.1.0
add address=10.89.5.14/24 interface=wlan1 network=10.89.5.0
/ip dhcp-server network
add address=192.168.1.0/24 gateway=192.168.1.254
/ip dns
set allow-remote-requests=yes servers=86.109.64.5,193.194.159.224
/ip firewall address-list
add address=86.109.64.0/27 list=support
add address=192.168.88.0/24 list=support
add address=10.0.0.0/8 list=support
add address=86.109.64.0/19 comment="Ezt ki lehet torolni, csak a beallitashoz kell" list=support
#error exporting /ip firewall calea
/ip firewall filter
add action=accept chain=input comment=telnet,ssh,ftp dst-port=21-23 protocol=tcp src-address-list=support
add action=drop chain=input comment=telnet,ssh,ftp dst-port=21-23 protocol=tcp
add action=accept chain=input dst-port=2000 protocol=tcp
add action=accept chain=input protocol=tcp src-port=2000
add action=add-src-to-address-list address-list=Syn_Flooder address-list-timeout=30m chain=input comment="Add Syn Flood IP to the list" connection-limit=30,32 protocol=tcp tcp-flags=syn
add action=drop chain=input comment="Drop to syn flood list" src-address-list=Syn_Flooder
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="Port Scanner Detect" protocol=tcp psd=21,3s,3,1
add action=drop chain=input comment="Drop to port scan list" src-address-list=Port_Scanner
add action=jump chain=input comment="Jump for icmp input flow" jump-target=ICMP protocol=icmp
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="NMAP FIN Stealth scan" protocol=tcp tcp-flags=fin,!syn,!rst,!psh,!ack,!urg
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="SYN/FIN scan" protocol=tcp tcp-flags=fin,syn
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="SYN/RST scan" protocol=tcp tcp-flags=syn,rst
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="FIN/PSH/URG scan" protocol=tcp tcp-flags=fin,psh,urg,!syn,!rst,!ack
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="ALL/ALL scan" protocol=tcp tcp-flags=fin,syn,rst,psh,ack,urg
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="NMAP NULL scan" protocol=tcp tcp-flags=!fin,!syn,!rst,!psh,!ack,!urg
add action=drop chain=input comment="Block all access to the winbox - except to support list # DO NOT ENABLE THIS RULE BEFORE ADD YOUR SUBNET IN THE SUPPORT ADDRESS LIST" dst-port=8291 protocol=tcp src-address-list=!support
add action=accept chain=input comment="Accept to established connections" connection-state=established
add action=accept chain=input comment="Accept to related connections" connection-state=related
add action=accept chain=input comment="Full access to SUPPORT address list" src-address-list=support
add action=accept chain=input dst-address=255.255.255.255
add action=log chain=input comment="Drop anything else! # DO NOT ENABLE THIS RULE BEFORE YOU MAKE SURE ABOUT ALL ACCEPT RULES YOU NEED" disabled=yes
add action=drop chain=input comment="Drop anything else! # DO NOT ENABLE THIS RULE BEFORE YOU MAKE SURE ABOUT ALL ACCEPT RULES YOU NEED"
add action=accept chain=ICMP comment="Echo request - Avoiding Ping Flood" icmp-options=8:0 limit=10,15 protocol=icmp
add action=accept chain=ICMP comment="Echo reply" icmp-options=0:0 protocol=icmp
add action=accept chain=ICMP comment="Time Exceeded" icmp-options=11:0 protocol=icmp
add action=accept chain=ICMP comment="Destination unreachable" icmp-options=3:0-1 protocol=icmp
add action=accept chain=ICMP comment=PMTUD icmp-options=3:4 protocol=icmp
add action=drop chain=ICMP comment="Drop to the other ICMPs" protocol=icmp
add action=jump chain=output comment="Jump for icmp output" jump-target=ICMP protocol=icmp
/ip firewall nat
add action=masquerade chain=srcnat src-address=192.168.1.0/24
add action=dst-nat chain=dstnat dst-port=88,8080,554,9010,9020 in-interface=all-ppp protocol=tcp to-addresses=192.168.1.80
add action=dst-nat chain=dstnat dst-port=6881-6890,21,443,5000-5001,500,1701,1723 in-interface=all-ppp protocol=tcp to-addresses=192.168.1.60
add action=dst-nat chain=dstnat dst-port=4500 in-interface=all-ppp protocol=udp to-addresses=192.168.1.60
add action=dst-nat chain=dstnat dst-port=8090 in-interface=all-ppp protocol=tcp to-addresses=192.168.1.60 to-ports=80
add action=dst-nat chain=dstnat dst-port=8088 in-interface=all-ppp protocol=tcp to-addresses=192.168.1.80 to-ports=8088
/ip route
add distance=100 gateway=10.89.5.1
/ip service
set www address=86.109.64.0/27
set api address=86.109.64.0/27
set api-ssl address=86.109.64.0/27
/ip ssh
set allow-none-crypto=yes forwarding-enabled=remote
/snmp
set contact=admin@rlan.hu enabled=yes location=Papa
/system clock
set time-zone-name=Europe/Budapest
/system identity
set name=gw-bdrszcs
/system leds
set 0 interface=wlan1
/system logging
add action=remote topics=info
add action=remote topics=critical
add action=remote topics=error
add action=remote topics=warning
/system ntp client
set enabled=yes primary-ntp=86.109.64.5
/system scheduler
add interval=6d name=mentes on-event=mentes policy=ftp,reboot,read,write,policy,test,password,sniff,sensitive start-date=jan/26/2016 start-time=16:35:45
/system script
add dont-require-permissions=no name=mentes owner=admin policy=ftp,reboot,read,write,policy,test,password,sniff,sensitive source="/system\_backup save name=backup\r\n/tool e-mail send to=\"magic@magicnet.hu\" subject=([/system identity get name] . \" Backup\") file=backup.backup\r\n/export file=export\r\n/tool e-mail send to=\"magic@magicnet.hu\" subject=([/system identity get name] . \" export\") file=export.rsc"
/system watchdog
set auto-send-supout=yes send-email-from=gw-bdrszcs@magicnet.hu send-email-to=magic@magicnet.hu send-smtp-server=86.109.64.10 watch-address=10.89.6.1
/tool e-mail
set from=gw-bdrszcs@magicnet.hu
/tool graphing interface
add
/tool graphing queue
add
/tool graphing resource
add