#              model: CubeG-5ac60ad
#      serial-number: E2A30EB51C40
#      firmware-type: ipq4000L
#   current-firmware: 6.48.4
#   installed-version: 7.15.3
# Flags: U - UNDOABLE
# Columns: ACTION, BY, POLICY, TIME
#   ACTION                   BY     POLICY  TIME               
# U user mentes added        admin  write   2024-10-03 13:18:58
#                                   policy                     
# U user group backup added  admin  write   2024-10-03 13:18:58
#                                   policy                     
# 
# software id = LN20-PJFD
#
# model = CubeG-5ac60ad
# serial number = E2A30EB51C40
/interface bridge
add admin-mac=2C:C8:1B:5B:73:AE auto-mac=no name=bridge port-cost-mode=short
add name=bridge-vlan2839
/interface ethernet
set [ find default-name=ether1 ] l2mtu=1620 mtu=1600
/interface wireless
set [ find default-name=wlan1 ] adaptive-noise-immunity=ap-and-client-mode band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX country=no_country_set disabled=no frequency=auto frequency-mode=superchannel mode=station-bridge nv2-preshared-key=dsjnf999 nv2-security=enabled scan-list=5000-6000 ssid=RLAN_HUOM wireless-protocol=nv2-nstreme
/interface wireless nstreme
set wlan1 enable-nstreme=yes
/interface w60g
set [ find ] disabled=no frequency=64800 mode=station-bridge name=wlan60-1 password=dsjnf999 region=no-region-set scan-list=58320,60480,62640,64800,66000 ssid=RLAN_HUOM
/interface bonding
add mode=active-backup name=bond1 primary=wlan60-1 slaves=wlan60-1,wlan1
/interface lte apn
set [ find default=yes ] ip-type=ipv4 use-network-apn=no
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk comment=defconf disable-pmkid=yes mode=dynamic-keys supplicant-identity=MikroTik wpa2-pre-shared-key=90fa-7bc7
/ip smb users
set [ find default=yes ] disabled=yes
/ppp profile
add bridge=bridge-vlan2839 name=l2tp
/interface l2tp-client
add allow-fast-path=yes connect-to=86.109.64.245 disabled=no mrru=1600 name=l2tp-out1 password=Pwhu423fte2 profile=l2tp user=bpeotvos
/queue simple
add burst-limit=120M/120M burst-threshold=90M/90M burst-time=1m/1m disabled=yes max-limit=100M/100M name=Omnilan target=86.109.70.152/29
/routing bgp template
set default disabled=no output.network=bgp-networks
/routing ospf instance
add disabled=no name=default-v2
/routing ospf area
add disabled=yes instance=default-v2 name=backbone-v2
/snmp community
set [ find default=yes ] addresses=86.109.64.0/27
/system logging action
set 3 remote=86.109.64.16
/interface bridge port
add bridge=bridge-vlan2839 ingress-filtering=no interface=ether1 internal-path-cost=10 path-cost=10
add bridge=bridge ingress-filtering=no interface=bond1 internal-path-cost=10 path-cost=10
/interface bridge settings
set use-ip-firewall=yes
/ip firewall connection tracking
set udp-timeout=10s
/ipv6 settings
set disable-ipv6=yes max-neighbor-entries=8192
/interface ovpn-server server
set auth=sha1,md5
/ip address
add address=10.1.35.15/24 interface=bridge network=10.1.35.0
/ip dns
set servers=86.109.64.5,86.109.64.66
/ip firewall address-list
add address=86.109.64.0/27 list=support
add address=10.0.0.0/8 list=support
add address=86.109.64.0/19 comment="Ez torolheto" list=support
add address=192.168.88.0/24 list=support
/ip firewall filter
add action=accept chain=input comment=telnet,ssh,ftp dst-port=21-23 protocol=tcp src-address-list=support
add action=drop chain=input comment=telnet,ssh,ftp dst-port=21-23 protocol=tcp
add action=accept chain=input comment="Bandwidth test" protocol=tcp src-address-list=support src-port=2000
add action=accept chain=input comment="Bandwidth test" dst-port=2000 protocol=tcp src-address-list=support
add action=add-src-to-address-list address-list=Syn_Flooder address-list-timeout=30m chain=input comment="Add Syn Flood IP to the list" connection-limit=30,32 protocol=tcp tcp-flags=syn
add action=drop chain=input comment="Drop to syn flood list" src-address-list=Syn_Flooder
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="Port Scanner Detect" protocol=tcp psd=21,3s,3,1
add action=drop chain=input comment="Drop to port scan list" src-address-list=Port_Scanner
add action=jump chain=input comment="Jump for icmp input flow" jump-target=ICMP protocol=icmp
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="NMAP FIN Stealth scan" protocol=tcp tcp-flags=fin,!syn,!rst,!psh,!ack,!urg
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="SYN/FIN scan" protocol=tcp tcp-flags=fin,syn
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="SYN/RST scan" protocol=tcp tcp-flags=syn,rst
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="FIN/PSH/URG scan" protocol=tcp tcp-flags=fin,psh,urg,!syn,!rst,!ack
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="ALL/ALL scan" protocol=tcp tcp-flags=fin,syn,rst,psh,ack,urg
add action=add-src-to-address-list address-list=Port_Scanner address-list-timeout=1h chain=input comment="NMAP NULL scan" protocol=tcp tcp-flags=!fin,!syn,!rst,!psh,!ack,!urg
add action=drop chain=input comment="Block all access to the winbox - except to support list # DO NOT ENABLE THIS RULE BEFORE ADD YOUR SUBNET IN THE SUPPORT ADDRESS LIST" dst-port=8291 protocol=tcp src-address-list=!support
add action=accept chain=input comment="Accept to established connections" connection-state=established
add action=accept chain=input comment="Accept to related connections" connection-state=related
add action=accept chain=input comment="Full access to SUPPORT address list" src-address-list=support
add action=accept chain=input dst-address=255.255.255.255
add action=log chain=input comment="Drop anything else! # DO NOT ENABLE THIS RULE BEFORE YOU MAKE SURE ABOUT ALL ACCEPT RULES YOU NEED" disabled=yes
add action=drop chain=input comment="Drop anything else! # DO NOT ENABLE THIS RULE BEFORE YOU MAKE SURE ABOUT ALL ACCEPT RULES YOU NEED"
add action=accept chain=ICMP comment="Echo request - Avoiding Ping Flood" icmp-options=8:0 limit=10,15 protocol=icmp
add action=accept chain=ICMP comment="Echo reply" icmp-options=0:0 protocol=icmp
add action=accept chain=ICMP comment="Time Exceeded" icmp-options=11:0 protocol=icmp
add action=accept chain=ICMP comment="Destination unreachable" icmp-options=3:0-1 protocol=icmp
add action=accept chain=ICMP comment=PMTUD icmp-options=3:4 protocol=icmp
add action=drop chain=ICMP comment="Drop to the other ICMPs" protocol=icmp
add action=jump chain=output comment="Jump for icmp output" jump-target=ICMP protocol=icmp
add action=fasttrack-connection chain=forward connection-state=established,related disabled=yes hw-offload=yes protocol=tcp
add action=accept chain=forward connection-state=established,related disabled=yes protocol=tcp
add action=drop chain=forward comment="Nem kiadott ip-k eldobalasa" src-address=86.109.70.157
add action=drop chain=forward comment="Nem kiadott ip-k eldobalasa" src-address=86.109.70.158
/ip route
add disabled=no dst-address=0.0.0.0/0 gateway=10.1.35.1
/ip service
set www address=86.109.64.0/27
set api address=86.109.64.0/27
set api-ssl address=86.109.64.0/27
/ip smb shares
set [ find default=yes ] directory=/flash/pub
/routing bfd configuration
add disabled=no
/snmp
set contact=admin@rlan.hu enabled=yes location=Budapest
/system clock
set time-zone-name=Europe/Budapest
/system identity
set name=gw-eotvos-lehetutca1
/system logging
add action=remote topics=info
add action=remote topics=error
add action=remote topics=critical
add action=remote topics=warning
/system note
set show-at-login=no
/system ntp client
set enabled=yes
/system ntp client servers
add address=time.rlan.hu
/system scheduler
add interval=6d name=mentes on-event=mentes policy=ftp,reboot,read,write,policy,test,password,sniff,sensitive,romon start-date=2021-05-19 start-time=10:10:51
/system script
add dont-require-permissions=no name=mentes owner=admin policy=ftp,reboot,read,write,policy,test,password,sniff,sensitive,romon source="/export file=export\r\n/tool e-mail send from=\"backup@rlan.hu\" to=\"backup@rlan.hu\" subject=([/system identity get name] . \" export\") file=export.rsc\r\n/system backup save name=backup\r\n/tool e-mail send from=\"backup@rlan.hu\" to=\"backup@rlan.hu\" subject=([/system identity get name] . \" Backup\") file=backup.backup"
/system watchdog
set ping-start-after-boot=55m
/tool e-mail
set from=gw-eotvos-lehetutca1@magicnet.hu server=mail.rlan.hu
/tool graphing interface
add
/tool graphing queue
add
/tool graphing resource
add
/user group
add name=backup policy="ssh,read,sensitive,!local,!telnet,!ftp,!reboot,!write,!policy,!test,!winbox,!password,!web,!sniff,!api,!romon,!rest-api"